Kit for assembling a boat on radio control. RC Model

The kit is in good working order. It has four buttons combined in pairs. This is such a soldering. Even a piece of double-sided tape for fastening the battery pack. I did not have a direct need to purchase such a thing; I just crawled through the expanses of shops in order to buy something to pass the evening, put my hands on it and distract my son (8 years old) from the tablet.
As for the surface part; here are electric motors and gear reduction gear, to the shaft of which the second end of the spring is attached. Although I deliberately did it in such a way that the nose would not be overwhelmed by the wave.
From the reverse side, too, a similar picture. Among other things, there is a simple but sensible step-by-step assembly instruction.
All the parts were distributed in two bags, and they, in turn, were placed in a foam box (it was not included in the photo). I don’t know how many knots it is) And do not put it in the kit, well, sorry, this is redneck). Even a cursory glance is enough to understand that there is no production culture at all when assembling radio-electronic components. Fully corresponds to the description of the seller and all the declared characteristics. Yes, indeed, the review is somewhat out of season, but the set is interesting, efficient and deserves attention.
4-5-6 Here you can see that for the sake of simplicity, the model is flat-bottomed and does not have a rudder. More than four meters there is no signal or responds to single commands. RC Model

Mounting holes are already drilled in them, so for assembly you only need a thin Phillips screwdriver. And a few cogs-shpuntiki generally superfluous (spare) left. There is everything you need to assemble the model.
Full speed ahead! According to my estimates, the speed is about 0.5 meters per second. This lot seemed to me suitable, and the price was acceptable, and I made an order.
The antenna is a spring-loaded piece of single wire.
After connecting the battery pack (4*AA) and https://tonaton.co.ke/s_31-garbage-trucks switching the necessary wires, you can proceed to sea trials.

The photo above, as you may have guessed, shows the underwater part of the bottom at the stage of assembling the propeller assembly (the left one has not yet been installed). The kit is self-sufficient.
This is not a mechanical bend. Marking TXM 8A978S ZYF22AC Maneuvering is carried out by screws, the rotation of which is transmitted through a flexible spring drive. There are two plates: on the bottom and deck.
And so, the basis of the hull of the boat is a molded piece of foamed PVC, through the aft part of which textolite plates are fixed with studs, which serve as the basis of the entire structure. The son was in a hurry to start assembling, so there will be no bulk photos of parts, don’t blame me! The center of gravity is slightly shifted aft, but this moment can be easily adjusted by estimating the location of the batteries on the deck. – The entire assembly is https://jiji.ng/ikorodu/297-generators/honda carried out with one single tool – a thin Phillips screwdriver. The screws go in tightly, I would even say with an interference fit, so a certain strength in
structures are present. The courier brought the parcel to the house, by prior arrangement. And although the delivery was carried out by a courier service, the package was soft, but the packaging did its job, saved the contents.

Kit for assembling a boat on radio control. 1-2-3
Well, the control controller board, which is fastened with a single screw on the rack, completes the whole design. At a distance of up to four meters, the pairing breaks and depends on the relative position of the receiver and transmitter antennas. ± Sloppy assembly of electronic components. I had to wait a long time, about two months, one thing pleases the courier brought the parcel to the house. Everything is clear, this affects the bending of the screws and the shape of the base. The remote control and the controller are capable of implementing such a mode. Powered by two AA batteries. In the review, there are several photos of the assembly stages, a closer view of the board and a video from the bathroom And in general, the appearance of the finished toy is far from aesthetic. Well, to tell the truth, my son and I were satisfied with the toy: we spent time, and indulged, and plans As for the controller itself, I don’t know anything about it, but I still managed to photograph it. The control panel is delivered already assembled. But in terms of elementary maneuverability, the boat turned out to be relatively nimble. Left/right channel and backward/forward movement, respectively. But oddly enough, everything works. While, of course, you should be fully aware that this model is not built for records, this is nothing more than a fun self-assembly toy. I confirm the declared range of three meters, at this distance the reception is stable. Full back! even visually it is decently slower. ± Good service in the store. Let me remind you that the turns are carried out by screws, which means that the maximum angular velocity will be achieved with multidirectional rotation of the screws. IMHO, a pair of cable ties in https://tonaton.com/s_302-ambulance-stretchers the kit is asking for it.

Leave a Reply